(plunger type cylinder,produced by Hengyu Hydraulic Cylinder Factory）

plunger type cylinder are widely used ，because of long service life，smooth movement，high work efficiency.So our company has designed plunger type cylinder for our customers.

Introduction to plunger type cylinder:

If the seal of the plunger type cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

In the case of serious wear on the inner surface of the plunger type cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the plunger type cylinder manufacturing process for replacement. The plunger type cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

If the plunger type cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the plunger type cylinder. The internal parts of the plunger type cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the plunger type cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the plunger type cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the plunger type cylinder bore processing is out of whack. Because the piston and plunger type cylinder, guide rail and piston rod are relative If the plunger type cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling plunger type cylinder weight composition and calculation. The weight of the plunger type cylinder is composed of the plunger type cylinder diameter, the outer diameter and weight of the plunger type cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

plunger type cylinder is the most important part of construction machinery, the traditional processing method is: broaching plunger type cylinder block - fine boring plunger type cylinder block - grinding plunger type cylinder block. The rolling method is: broaching plunger type cylinder block - fine boring plunger type cylinder block - rolling plunger type cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the plunger type cylinder block is about 1-2 days, rolling 1 meter of the plunger type cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the plunger type cylinder increases by 25%. If the plunger type cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality plunger type cylinders, you must take the rolling production process. After the plunger type cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Answers to some questions about plunger type cylinder:

What is a differential cylinder?
The differential cylinder is by connecting the return oil of the rod cavity through the pipeline, allowing them to flow into the rodless cavity, thereby speeding up the extension speed of the piston rod. In fact, the cylinder is still the cylinder, but the oil circuit is related to the connection. The oil connection mode in which both chambers of a single rod hydraulic cylinder are fed hydraulic oil is called differential connection.

Why does the cylinder pop out of itself when it stops?
This situation has two possibilities, 1. There is more air in the system, so exhaust the gas. 2. The back pressure of the oil return is relatively large, check the oil return filter, check whether the cylinder has a rod cavity buffer is too tight, and choose a 3-position 4-way M-type valve for the reversing valve. In addition, after the shutdown, manually change the reversing valve back and forth several times, it should not rise out.